It's like Beauty and the Beast, right? The end result doesn't look so bad after all. What you don't see in this picture are the many
And now, for the gory details. The first thing I did was remove the chair seat. Which turned out to be a total pain in the a**. See, I was under the impression that most chair seats are attached to the base by means of several screws. However, this particular Beast had the seat nailed into the base, from the top. The nails were conveniently covered by the floral ribbon that you see surrounding the red fabric of the seat. The nice lady who sold me this chair on Craigslist informed me that this chair belonged to her mother, so I estimated it to be approximately from the 1930s. Which means that those nails had approximately 80 years or so to marinade in this chair and turn to rusty projectile missiles upon my attempt to remove them from the chair seat. After battling the seat for an hour, I realized that it was broken anyway (it was cracked on the bottom), so I might as well stop trying to salvage it and make a new seat later. (Did I mention that I had never made a chair seat before?) This was quite a satisfying conclusion, actually, because now I had the freedom to go to town with this chair seat and just completely rip it off the chair without worrying about the consequences. Which I proceeded to do with great vigor.
With the seat off the chair, it was time to remove the old paint. So I went on my first of many trips to Home Depot to pick up some supplies. Normally (I sound like an expert already, right?), I would just sand the sucker down, then maybe prime and paint. But given the age of the chair, I worried about the possibility of lead paint. Now, if I had thought about this for about a minute, I would have bought a $6 kit from Home Depot to determine whether or not there was lead in the paint. But that's not really my style, so I decided to assume that the chair was covered with lead paint, and proceed with caution. At the store, I asked an employee about the more environmentally friendly option for a paint stripper (that promised a citrus smell). He claimed it works fine, just a bit slower than the nastier stuff, so I bought a can of that. Back home, I took my chair outside on our tiny balcony and sprayed it with the stripper. Although the label on the can promised that the paint would start peeling within about half an hour, after leaving the chair overnight, I didn't see a single damn bubble. Turns out this stuff works best above 60 F. Inconveniently enough, we were well into November by the time I started this
Obviously, a little issue like cold weather wasn't going to stop me. So I kept spraying (and later, "painting") the chair with the paint stripper, and then scrubbing the hell out of it to get the paint off. When I got most of the paint off, I decided this was good enough. Which was my first mistake (or my first MAJOR mistake). Of course I didn't know this at the time, but the old paint would later bleed through the primer and the new paint. Lesson learned. Anyway, following the instructions on the can, I had to remove all the paint stripper with mineral spirits. The next thing I learned was that even if the container says "odorless", that mean absolutely nothing if it is followed by the words "mineral spirits". That stuff stunk to high heavens. So, considering it was already the beginning of December at this point, I was eager to be done with this step and take my project indoors.
After the paint was mostly off, I sanded down the chair. Then, I proceeded to prime it. Looking back, I probably should have used a latex primer (since I was going to follow up with latex paint anyway), but since the blogosphere claimed that oil-based primer sticks much better, and can be used with latex paint, this is what I went with. This, of course, upped my count of nasty, stinky chemicals used in this project to three (so far). That, and it was messy, and I had to wash my paint brush with "odorless" mineral spirits. (I ended up throwing away the expensive Purdy brush because I didn't have it in me to properly clean it). Anyway, after one layer of primer, the chair looked like this:
I still have no idea if that was enough coverage or not, but for whatever reason, I decided to do a second layer of primer. Which was probably my second major mistake. Maybe I should have sanded it between layers of primer. Maybe one layer was enough. Either way, the second layer looked even worse. Although the coverage was better, the primer was now drippy in places, and it had dried that way, so I had to sand some parts again. (Most bloggers make this all look so easy. It must be because they actually know what they are doing. But I didn't have a clue, and I am telling it exactly like the mess that it was.)
Anyway, at this point I decided that I had enough of priming, and it was time to paint. I used white, no-VOC paint (Freshaire brand), and I have to say this was actually a really nice paint to work with. No nasty fumes to deal with, and it went on smooth like butter. After two coats, the chair looked like this:
Finally, I was beginning to like my chair. Some of the old paint was bleeding through a little at this point, but not enough to bother me, so I let it go. See, making over a chair is like a Zen experience. Minus the nasty smells. It was time to make a new seat. At work, I found a discarded piece of 1/4 inch plywood (yay for free supplies). I measured out a 16 inch diameter circle and cut it out on a band saw (I was lucky enough to have access to the band saw at work). Then I went to JoAnn's and purchased foam, batting, and fabric. I cut out a corresponding circle from the the foam that I had bought and secured it lightly onto the top of the plywood with some double-sticky tape. Then I covered the foam with a layer of batting and stapled it to the underside of the plywood with my newly acquired staple gun.
At this point, I made my third major mistake. I probably should have covered my seat with three or four layers of batting to make it softer. Because now, sitting on this chair as I write this blog post, I am wishing it was a bit cushier. Oh well, let it go, Anna, let it go. After the batting was on, I repeated the stapling process with the pretty green and white fabric I had purchased. It was time to attach the seat to the chair. If you scroll up to the picture of the primed chair, you will notice that the perimeter of the seat base is actually full of holes. I suspect that the chair seat was actually caned at some point. Which was great, because I didn't have to drill any new holes in the chair to attach my seat. I decided to screw it in from the bottom with three screws using three of those holes. I pre-drilled into the new seat (not all the way, maybe 2/3 of the thickness of the plywood) and screwed in the seat. My ugly duckling had become a swan.
And thus concludes my first adventure into DIY land. I would do a cost breakdown, but honestly that would be rather